|
| 品牌 | 德國KAYSEN |
| 連接形式 | 法蘭 |
| 材質 | 鑄鐵、不銹鋼、鋁合金、氟墮料 |
| 型號 | KAYSEN |
| 工作壓差 | 0 |
| 適用范圍 | 水、污水、石油、化工、電子、飲料、食品 |
| 壓力環境 | 常壓 |
| 介質溫度 | 250℃ |
| 驅動方式 | 氣動 |
| 適用介質 | 水 |
鑄鋼氣動隔膜泵|原裝隔膜泵
凱森（KAYSEN）品牌，*的十*，我們的鑄鋼氣動隔膜泵在SchwbischGmnd生產。
凱森始終堅持“重質量，講信譽”為宗旨。產品現暢銷全國各地，并已
KAYSEN凱森冷凝泵概述
鑄鋼氣動隔膜泵是凱森開發的新一代代氣動隔膜泵，質量可靠使用壽命長，即能抽送流動的液體，又能輸送一些不易流動的介質，具有自吸泵、潛水泵、屏蔽泵、泥漿泵和雜質泵等輸送機械的許多優點。
主要特點：
不需灌引水，吸程高達5米，揚程達70米，出口壓力≧7bar
該泵無旋轉部件，沒有軸封，隔膜等抽送的介質與泵的運動部件、工件介質完全隔開，所輸送的介質不會向外泄漏。所以抽送有毒、易揮發或腐蝕性介質時，不會造成環境污染和危害人身安全
不必用電，在易燃、易爆場所使用安全可靠
流動寬敞，通過性能好，允許通過*顆粒直徑達10毫米。抽送泥漿、雜質時，對泵磨損甚微
揚程、流量可通過氣閥開度實現無級調節(氣壓調節在1-7bar之間)
可輸送較粘的液體(粘度在1萬厘泊以下)
本泵無須用油潤滑，即使空轉，對泵也無任何影響
可以浸沒在介質中工作
使用方便、工作可靠、開停只需簡單地打開和關閉氣體閥門，即使由于意外情況而長時間無介質運行或突然停機泵也不會因此而損壞，一旦超負荷，泵會自動地停機，具有自我保護性能，當負荷恢復正常后，又能自動啟動運行
泵輸送的介質不會接觸到配氣閥，聯桿等運動部件，不像其他類型的泵因轉子、活塞、齒輪、葉片等部件的磨損而使性能逐步下降
主要優點
使用壽命長
使用方便
壓力足
噪音低
做工精細
不會停頓
結構簡單、易損件少
安裝、維修方便
安全可靠
主要應用：
粘合劑和膠水、全部種類可用泵吸取
塑料氣動隔膜泵可以用于吸油漆、樹膠、顏料
油井鉆好后，用氣動隔膜泵吸沉積物及灌漿
各種瓦、瓷、磚器及陶器釉漿
吸各種污水
氣動隔膜泵可以用于為油輪，駁船清倉吸取倉內污水
吸各種乳劑和填料
礦井、坑道、隧道、選礦、礦渣中的積水、泵吸水泥灌漿及灰漿
吸啤酒花及發酵粉稀漿、糖漿、糖密
氣動隔膜泵可以吸各種磨料、腐蝕劑、石油及泥漿、清洗油垢及一般容器
隔膜泵泵吸各種橡膠漿
各種強酸、強堿、強腐蝕液體
可以吸各種劇毒、易燃、易揮發液體
氣動隔膜泵作為各種固液體分離設備的前級送壓裝置
吸各種高溫液體*可耐150度
氣動隔膜泵可以吸花生醬、泡菜、土豆泥、小紅腸、果醬蘋果漿、巧克力等
基本的預防性維護保持泵流動
執行預防性維護有助于防止泵停機
有人說：“你不知道自己得到了什么，直到它消失?！睂τ谌魏卧?jīng)忽視泵的人來說，這個概念可能是太熟悉了?？煽康谋迷谡９ぷ鲿r并不真正被認可，但是如果泵的性能下降，或者更糟糕的是，該設備完全停止工作，那么可靠性會被錯過。為避免泵停機和隨后的麻煩，必須遵守預防性維護計劃。
每天開始泵檢查。最重要的日常檢查之一是發動機油的質量和水平。骯臟的油可能會導致嚴重的問題并降低發動機的使用壽命; 同樣，如果數量不足。根據制造商的建議更換機油或根據需要添加以達到水平。
檢查汽油水平，確保油箱已滿，或者至少滿足一天的使用量。同時尋找任何燃油或漏油跡象。如果液體滴落，請檢查該區域是否有可能需要擰緊或更換的部件。
清潔或可能更換空氣過濾器是另一個可以防止重大損壞的重要做法。堵塞，潮濕或骯臟的空氣過濾器會導致動力損失，并通過允許污垢或水進入敏感區域來縮短發動機的使用壽命。泡沫元件可以清潔和重復使用，所以每天檢查一下就可以了。如果過濾器已損壞或缺少大塊，請將其更換。對于紙質空氣過濾器，操作員應按照推薦的時間表及時更換。
定期檢查軟管的狀況。如果它們磨損，磨損或有任何漏洞，則氣隙可能會導致泵失去吸力。修補任何孔并密封泄漏的接頭。應該更換嚴重磨損的軟管。*，檢查機器的其余部分是否有螺栓，螺母或零件松動。
在所有的手術前檢查中，日常維護中最重要的事情可能就是在開始之前啟動泵。運行干燥的泵會損壞密封件，導致更多問題的連鎖反應。如果是自吸泵，只需加水即可。術語“自吸”有點用詞不當，因?yàn)槊看问褂脮r必須將水添加到泵中。然后泵將接管，在蝸殼內建立壓力并開始排放。
不太頻繁的檢查
一旦泵已經準備好了，就可以開始工作了。除日常檢查外，泵還需要其他維護檢查和服務。雖然這些不需要每天完成，但它們對泵的使用壽命至關重要，并應定期按計劃進行。一般來說，優質的泵引擎可以運行幾千小時，并且遵循推薦的維護計劃只能增加該時間和泵的投資回報率。
有幾件事情需要每月檢查幾次，其他事件則更少。例如，紙張空氣過濾器應在需要時更換。雖然泡沫過濾器可以清洗并重新使用，但是當它開始分解或分解時，需要更換。
臟的火花塞可能會導致功率下降和起動性能差，因此應每半月檢查一次火花塞是否有殘留油污，污垢，損壞或積碳過多的情況。用鋼絲刷或火花塞清潔器清潔火花塞。立即更換任何火花塞與裂紋瓷。
每年都要對泵進行徹底檢查，檢查是否有骯臟，破損或未對齊的部件。這些部件可能會導致發動機或泵部件出現問題。檢查整臺機器可以*地了解需要清潔和修理的部件。
值得注意的是，灰塵狀況通常會縮短正常服務之間的時間長度，因?yàn)?的灰塵會堵塞過濾器元件或污染燃料和機油。取決于泵的環境，可能需要調整維護計劃以適應低于*條件。
故障排除提示
即使定期進行適當?shù)念A(yù)防性維護計劃，泵仍然可能會遇到問題。這很不幸，但很常見。知道如何尋找并快速解決問題將使問題不再成為更昂貴，耗時的修復。
如果泵不啟動，罪魁禍?zhǔn)卓赡苁侨~輪或發動機。如果葉輪粘住，只需拆下泵蓋，清潔并重新安裝。至于引擎，幾個不同的東西可能會影響它，并阻止從開始。
首先要檢查的是火花塞。如果它被油渣，氣體或碳污染，請清潔它。如果它損壞了，請更換它。如果它干凈無損，請將其連接到插頭蓋并將插頭與發動機機身接地。拉起動器，看看火花是否微弱或不存在。如果新的或清潔的插頭沒有點燃，則點火系統可能有故障，可能需要更換。
如果火花塞松動或插頭浸濕燃油，發動機也可能無法啟動。如果火花塞是潮濕的，請檢查燃油旋塞是否關閉。如果是這樣，關閉阻風門拉桿并拉動起動手柄6次，看電極是否變濕。如果電極干燥，問題可能與化油器的燃料吸入有關。試著看看燃油停在發動機的哪里。
其他一些事情可能會導致泵不能自行灌注。首先檢查泵吸入側的漏氣情況; 如果需要，擰緊吸入軟管或管道。檢查排水塞，確保它完全擰緊。泵殼內的水不足也會阻止泵啟動。
發動機轉速也會影響泵送量。如果泵送量下降，則抽吸軟管可能太長或抽吸腔室上的零件松動可能需要重新擰緊。這也可能是由于需要降低高吸力，水通道漏水，機械密封磨損或斷裂或發動機輸出功率或速度下降造成的。
采取積極主動的預防措施，確保關鍵的維護服務不會被忽視，防止泵出現故障時產生多米諾骨牌效應，浪費時間并增加維修成本。這很簡單直接 - 泵的維護現在意味著更少的問題。遵循良好的維護計劃，例如上述步驟，是保持泵流量的*和*的方法之一。
Basic Preventive Maintenance to Keep Pumps Flowing
Performing preventive maintenance helps prevent pump downtime
It has been said, “You don’t know what you’ve got until it’s gone.” This concept can be all-too-familiar for anyone who has ever neglected a pump. A dependable pump isn’t truly appreciated when it’s working properly but that dependability is really missed if a pump’s performance declines, or worse, the unit stops working altogether. To avoid pump downtime and subsequent headaches, a preventive maintenance program must be followed.
Start each day with a pump inspection. Among the most important daily checks is the quality and level of engine oil. Oil that’s dirty can cause serious problems and decrease the life of an engine; likewise, if there’s an insufficient amount of it. Change the oil or add if necessary to reach the level as per manufacturer recommendation.
Check the gasoline level as well, making sure the tank is full, or at least full enough for the day’s usage. Also look for any evidence of fuel or oil leaks. If a fluid is dripping, inspect the area for any parts that may need to be tightened or replaced.
Cleaning or possibly changing the air filter is another important practice that can prevent significant damage. A clogged, wet or dirty air filter can lead to a loss in power and shorten the life of an engine by allowing dirt or water into sensitive areas. A foam element can be cleaned and reused, so it’s fine to check daily. If the filter has been damaged or is missing chunks, replace it. For paper air filters, operators should follow a recommended schedule for replacement in a timely fashion.
Inspect the condition of the hoses regularly, as well. If they are worn, frayed or have any holes, the air gaps will likely cause the pump to lose suction. Patch any holes and seal leaking joints. A severely worn hose should be replaced. Finally, check the rest of the machine for broken bolts, nuts or loose parts.
Of all the pre-operation checks, perhaps the most important thing to remember for daily maintenance is priming the pump before starting. Running a pump dry will damage the seals, causing a chain reaction of further problems. If it’s a self-priming pump, simply add water. The term “self-priming” is somewhat of a misnomer, as water must be added to the pump each time it is used. The pump will then take over, build pressure within the volute and begin discharging.
Less-frequent Checks
Once the pump has been prepped, it’s ready to go to work. In addition to daily checks, a pump requires other maintenance checks and services. While those don’t need to be done daily, they are crucial to the pump’s life and should be kept up with on a regular schedule. Generally, quality pump engines can operate for a few thousand hours, and following recommended maintenance schedules can only increase that time and the pump’s ROI.
A few things need to be checked a couple of times a month, others even less frequently. For instance, a paper air filter should be changed when needed. Although a foam filter can be cleaned and re-used, when it begins to disintegrate or come apart, replacement is necessary.
Dirty spark plugs can cause a decrease in power and poor starting performance, so the spark plugs should be checked semi-monthly for oil residue, dirt, damage or excessive carbon buildup. Clean spark plugs with a wire brush or spark plug cleaner. Immediately replace any spark plugs with cracked porcelain.
On an annual basis, give the pump a thorough inspection for dirty, broken or misaligned parts. Such parts can cause problems with the engine or pump components. Inspecting the entire machine gives the most comprehensive view of what needs to be cleaned and repaired.
It’s also worth noting that dusty conditions typically shorten the length of time between regular services, as extreme dust can clog filter elements or contaminate fuel and oil. Depending on the pump’s environment, maintenance schedules may need to be adjusted to accommodate for less than optimal conditions.
Tips For Troubleshooting
Even with a regular, proper preventive maintenance program, pumps may still experience problems. This is unfortunate, but common. Knowing what to look for and addressing it quickly will keep the problem from becoming a more expensive, time-intensive repair.
If a pump won’t start, the culprit is likely the impeller or engine. If the impeller is sticking, simply disassemble it by taking the pump cover off, clean and reinstall. As for the engine, several different things could affect it and prevent if from starting.
The first thing to check is the spark plug. If it’s dirty with oil residue, gas or carbon, clean it. If it’s damaged, replace it. If it’s clean and damage-free, connect it to the plug cap and ground the plug against the engine body. Pull the starter to see if the spark is weak or nonexistent. If a new or cleaned plug doesn’t spark, the ignition system could be faulty and may need replacement.
The engine also might not start if the spark plug is loose or if the plug is wet with fuel. If the spark plug is wet, check to see that the fuel cock is closed. If so, close the choke lever and pull the starter handle a half-dozen times to see if the electrode becomes wet. If the electrode is dry, the problem may be with the fuel intake of the carburetor. Try to see where the fuel stops in the engine.
A number of other things could cause a pump to not self-prime. Start by checking for air leaks on the suction side of the pump; tighten the suction hose or pipe, if needed. Check the drain plug, as well, to ensure that it has been tightened completely. Insufficient water inside the pump casing will also prevent the pump from priming.
Engine speed can affect pumping volume, as well. If the pumping volume has dropped, the suction hose may be too long or loose parts on the suction chamber may need re-tightening. This might also be caused by a high suction lift that would need to be lowered, water leaking from the water passage, a worn or broken mechanical seal or a drop in engine output or speed.
Adopting a proactive preventive approach ensures that crucial maintenance services won’t be neglected, preventing a domino effect of problems as the pump goes down, time is lost and repair costs add up. It’s simple and straightforward - pump maintenance now will mean fewer issues later. Following a good maintenance program, such as the steps detailed above, is among the best and most inexpensive ways to keep a pump flowing.
鑄鋼氣動隔膜泵|原裝隔膜泵
